Scotts Scott S 16 In Manual W

aluminum die casting wiper mount head

• Brand: NONE
• Packaging: carton, pallet
• Supply Ability: 140000/MONTH
• Min. Order: 1000 Piece/Pieces

The Aluminum Die Casting Wiper Mounting Head is a small part which is used for mounting the mating parts of wiper, this part have deep cavity, but the allowed draft angle is only 1.5 degree, what's more, the internal cavity has a lot of sharp teeth for locking the mating shaft part, in this situation, the part is...

Contact Now

Aluminum Die Casting Wiper Mounting Head

• Brand: NONE
• Packaging: carton, pallet
• Supply Ability: 300000/MONTH
• Min. Order: 1000 Piece/Pieces

The Aluminum Die Casting Wiper Mounting Head is a small part which is used as Mount head on windscreen wiper of bus, boat and car. The technology for this part is high pressure cold chamber die casting, the mold design is very important, like the location of the injection gate, runner, venting system etc. Incorrect...

Contact Now

Aluminum Windscreen Wiper Mount Head

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 300000/MONTH
• Min. Order: 2000 Piece/Pieces

The Aluminum Windscreen Wiper Mount Head is a small part which is used as Mount head of windscreen wiper system on bus, boat and car etc. The technology for this part is high pressure aluminum die casting, the mold design is very important, according to our ISO/TS:16949 Certificate, prior to the mold fabrication, the...

Contact Now

Die Casting Aluminum Mounting Head

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 300000/MONTH
• Min. Order: 2000 Piece/Pieces

The Die Casting Aluminum Mounting Head, the part is small, but similar to the other mounting head parts, it has a deep cavity, which is easier to make the part sticky to the mold, then during production, if the material sticked on the mold is not cleaned, it will damage the castings newly produced, so in the...

Contact Now

Aluminum Die Casting Housing of Pivot Side

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 30000/MONTH
• Min. Order: 1500 Piece/Pieces

Aluminum Die Casting Housing of Pivot Side, the part is a pivot side housing, similar to the pivot housing 421-1034 and 421-1035, this pivot side housing have two long threaded pillars, from these two pillars, there to be two shaft assembled. then with a mating motor side housing, the DC motor work inside the...

Contact Now

Double Shaft Pivot Housing

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 30000/MONTH
• Min. Order: 1500 Piece/Pieces

Double Shaft Pivot Housing, the part is also a kind of pivot housing on windscreen wiper system, which is applied to bigger buses, boat etc. The part is similar to the pivot housing 421-1034 but have two long pins, this pivot side housing have two long threaded pillars, from these two pillars, there to be two shaft...

Contact Now

Threaded Pivot Housing of Aluminum

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 30000/MONTH
• Min. Order: 1500 Piece/Pieces

Threaded Pivot Housing of Aluminum, the part is also a kind of pivot housing on windscreen wiper system, which is applied to bigger buses, boat etc. The part looks almost the same to the part number 421-1040 except the length of the two threaded pillar. It is almost 50 mm longer than pivot 421-1040. The most important...

Contact Now

Aluminum Die Casting Arm Channel

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 30000/MONTH
• Min. Order: 1500 Piece/Pieces

Aluminum Die Casting Arm Channel, the part is a bracket for passing and fixing the wire of the windscreen wiper, the standard carried for the die casting work of this part is GBT6414-CT4, this part has a lot of hollow-out structure, which need not only one slide to form. This part has a cylinder structure of φ15.7 mm,...

Contact Now

Aluminum Die Casting Drive Arm Crank

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 210000/MONTH
• Min. Order: 2000 Piece/Pieces

Aluminum Die Casting Drive Arm Crank, this part is used as driven arm crank on the windscreen wiper, the carried die casting criterion for this part is Grade GB-CT4, in application, the part will rotate with the driven structure of the wiper, so the mechanical property should at least satisfy tens of thousands of...

Contact Now

Aluminum Die Casting Wiper Motor Housing

• Brand: NONE
• Packaging: carton, PE pallet
• Supply Ability: 150000/MONTH
• Min. Order: 2000 Piece/Pieces

Aluminum Die Casting Wiper Motor Housing, it is a new part developed, the part is the major housing for the DC motor of the windscreen wiper. the cavity number for this part is 2, according to the required tolerance and dimensions, the difficult point of this part is the CNC machining work, the wall thickness is very...

Contact Now

Aluminum Die Casting Mount Bracket of Swing Arm

• Brand: NONE
• Packaging: Carton, PE pallet, Wooden Pall...
• Supply Ability: 45000/MONTH
• Min. Order: 2000 Piece/Pieces

Aluminum Die Casting Mount Bracket of Swing Arm, it is a part used on wiper system, the manufacturing technology is High Pressure Die Casting, a kind of cold chamber aluminum die casting, the material for this part is ADC-12, a Japanese standard aluminum. this material is supposed to conform to standard of JIS H...

Contact Now

Aluminum Die Casting Walking Motor Housing

• Brand: NONE
• Packaging: carton, PE pallet, PE flow box...
• Supply Ability: 200000/MONTH
• Min. Order: 4000 Piece/Pieces

Aluminum Die Casting Walking Motor Housing, the material for this part is ADC-12, a kind of material, having good fluidity, which is good for filling while die casting. This material is a good material to produce end cover, housing, gearbox, bracket etc. The composition of ADC-12 is:(Cu)1.5~3.5, (Si)9.6~12.0,...

Contact Now